TFT35 E3 V3.0 ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz; Upgrade the firmware by SD card. It is easy and convenient to operate.
SKR Mini E3 V2.0 ARM Cortex-M3 Series STM32F103RCT6 Master Controller with 32-bit Main Frequency of 72MHz Chip;Integrate UART mode of TMC2209 to simplify debugging of motherboard and driver.Reserve expansion ports for TMC2209 pins to facilitate users to use DIAG instead of Endstop.
TFT35 E3 V3.0 This display board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864 screen mode;Serial port screen mode supports two printing modes: SD card and U disk.
TFT35 E3 V3.0 LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.)
2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an for Arduino shield for easy service, part replacement, upgrade-ability and expansion. for Additionally, a number of for Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included.
A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro¡¯s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefullybefore using this product.
★ The main control uses the ARM-level Cortex-M4 series with a 32-bit dominant frequency of 168 MHz STM32F407ZGT6 chip, performance is greatly improved
★ Motor driver support :TMC5160,TMC2208,TMC2130,ST820,LV8729, DRV8825,A4988, etc.Display screen support: BIGTREETECH- 2.8 inch TFT,BIGTREETECH-3.5 inch TFT, LCD2004,LCD12864
★ Support Serial WIFI Online Printing. 9 motor drives, 3 extruders, 3 CNC fans. Reserve extended ports of BL Touch, PWM, ADC, UART, I2C and SPI;Support power-off continuous printing, material cut detection, shutdown and other functions;Support for dual Z axis printers
★ Equipped with highly modular open source firmware Marlin2.0, it is convenient for users to DIY and further-development, to avoid the worry of not being able to master the core code
High performance chipThe motherboard using 32-bit 120MHz ARM-class Cortex-M3 series LPC1769 main control chip; TFT35 E3 V3.0 display using ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHzthe performance is greatly improved;
Dual working modeSKR V1.4 Turbo on-board TMC-driven SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process,it can be used by simply inserting the jumper cap;
Multifunctional Control BoardSKR V1.4 Turbo board has functions such as continuous power on, material detection, shutdown after power off.
Multifunctional DISPLAYTFT35 E3 V3.0 touch screen reserve WIFI port, and WIFI function is realized by external WIFI module；Reserve the extension port of filament breaking detection (FIL-DET) and automatic shutdown after printing (PS-ON);
COMPATIBILITY: Suitable for Ender 3 v2, just plug it in and start printing. PLEASE NOTE: If your printer is Ender 3, Ender 3 pro or Ender-5, please contact us to get related firmware.
UPGRADED DRIVER: TMC2208 drivers is super quiet. Marlin 2.0.1 (1.0.1) and Bootloader installed, the firmware can be modified by ARDUNO with USB cable.
SAFETY: Thermal runaway protection is enabled, if the temperature rises out of control, the printer will stop heating and halt automatically. The Board is Optimized by Circuit, effectively solve the heating problem.
EASY to OPERATE: With USB Port, can be worked With E/Z/Y/X Axis Motor. Easy to install, easy to use.
TMC2208 is an ultra-quiet two-phase stepper motor drive chip, continuous drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision.
The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies; these are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing.
Compatible with existing 3D printer electronics, eliminating the expensive costs of redesign. It can replace the original TMC2100 A4988 DRV8825 LV8729, lower heat, especially for 3D printing market.
With this adapter you can test your SilentStepStick or flash the TMC2208 SilentStepStick with an USB-to-serial converter.
John Carter is the owner and CEO of AcedProducts.co—a popular online website that analyzes tens of thousands of reviews on various products to show you the bestsellers in any category. His goal is to make online shopping much easier than it's ever been by eliminating the need to guess which products are good and which ones are bad.
"Amazon, Amazon Prime, the Amazon logo and Amazon Prime logo are trademarks of Amazon.com, Inc. or its affiliates".